Introduction to the installation steps of spiral chutes: 1. Overview of the steps for mineral sorting in the chute, which belongs to the inclined surface flow sorting. The slurry is fed to a inclined chute or slope, and under the push of water, the mineral particle group is loose and layered. The upper layer of light minerals is quickly discharged from the groove, while the lower layer of minerals with high specific gravity stays in the groove or flows out at low speed from the bottom. After each is connected, the selected ore or tailings are obtained. Spiral concentrators are equipment for mining and beneficiation, making them ideal for sand mining and beneficiation in coastal, river, sand banks, and creeks. The equipment has a suitable structure, is installed in a simple and simple manner, occupies a small land area, has simple operability, stable beneficiation, clear separation, strong processing capacity, high efficiency beneficiation enrichment ratio, high recovery rate, and reliable operation. There are also advantages such as lightweight, moisture-proof, rust prevention, corrosion resistance, and strong adaptability to fluctuations in feed volume, concentration, particle size, and grade. 2、 Technical principle: The spiral chute separator is not limited to being placed on the cross (or tripod) of the support table. Equal slurry is slowly fed to the spiral groove surface through the feeding chute at the end of the rotating groove head for sorting. The bottom is equipped with a valve block type equipment acquisition slot, allowing other products to be divided into three types (or four types) according to grade along the radial direction. Change the selection width of each device by adjusting the position of the valve block. The product gathering bucket is a concentric circular tube that collects and exports the intercepted variable mineral flows separately. The transverse surface of the fiberglass chute has a very variable slope, which is suitable for the selection of fine particle materials. Introduction to Installation Steps of Spiral Chute: 
III. Advantages or Features: 1. High efficiency, high recycling rate, and correct mineral sorting; 2. No power required; 3. Lightweight, rust resistant, durable, wear resistant, and corrosion-resistant; 4. Low cost and long service life; 5. It is applicable to the fluctuation of feed volume, density, Granularity and grade; The friction force on the surface of 6 diamond sand makes the beneficiation efficiency better than other plastic surfaces. Introduction to the Installation Steps of the 
Spiral Chute 4. Structural Composition: The spiral chute consists of six parts: a feeding homogenizer, a feeding chute, a rotating chute, a product intercepting chute, an equipment gathering hopper, and a slot bracket (including a cross or triangular frame). The spiral groove connected by the rotating plate is a key accessory. The spiral plate is made of fiberglass (fiberglass reinforced coal gangue) and connected together through screws. The sorting surface of the rotating groove has one layer of pre designed durable wear-resistant layer. It has the advantages of lightweight, sturdy, and durable consumer goods. The spiral groove is equipped with a multi tube feeding homogenizer to screen minerals evenly, which is not cumbersome to operate. The mineral sorting equipment is freely stacked on the cross (or tripod) of the support table. The evenly distributed mortar is slowly fed to the spiral groove surface through the feeding groove installed at the head of the rotating groove, and the selection is carried out. The bottom of the rotating groove is installed in a valve block type new equipment to obtain the groove, allowing the sorted new products to be divided into three (or four) new products according to grade along the radial direction. Change the selection width of each new device by adjusting the position of the valve block. The new product gathering bucket is a concentric circular tube that distinguishes and converges the intercepted multi head ore flow. The cross-section of the fiberglass chute and the change in slope of the curve are particularly applicable for the selection of fine-grained materials. Introduction to the Installation Steps of Spiral Chutes 5. Application Scope: Fiberglass reinforced plastic chutes are used for processing 0.6-0.03 millimeters and this vein or placer ore. However, when the mud content is high, it is unfavorable for sorting. Currently, it has been widely used for processing iron ore, tungsten, tin ore, tantalum niobium ore, coastal and riverine minerals, and gold ore. Introduction to the Installation Steps of the 
Spiral Chute
- Home
- About us
Ganzhou Jinqiang Mining Equipment is a large-scale mining service company specializing in mining machinery manufacturing, mineral analysis, beneficiation process design, equipment selection, and equipment installation and debugging. The company has two large production bases, covering an area of 50000 square meters, with a workshop area of over 20000 square meters. We have 15 years of experience in manufacturing beneficiation equipment. The company's products have all passed ISO9001 and GOST international quality system certification. The gravity beneficiation equipment produced by the company, such as ore dressing shakers, jigs, and spiral chutes, is exported to more than 50 countries worldwide, with customers spread across all continents. - device
The company's core business is gravity beneficiation equipment, magnetic separation equipment, ore washing equipment, screening equipment, crushing and grinding equipment, flotation equipment, and mineral conveying equipment. Production of mineral processing equipment, sand gold processing equipment, gold ore processing equipment and Hematite processing equipment and other mineral processing equipment. Our company's gravity beneficiation equipment such as shakers, jigs, and spiral chutes account for 15% of the market share of gravity beneficiation equipment in China. - programme
The company has a variety of large-scale modern machining equipment, professional mechanical manufacturing engineers, mineral processing engineers, and professional equipment installation team. The company's core business is gravity separation equipment, magnetic separation equipment, ore washing equipment, screening equipment, crushing and grinding equipment, flotation equipment, and mineral conveying equipment. Our company's gravity separation equipment such as ore dressing shakers, jigs, and spiral chutes account for 15% of the market share of gravity separation equipment in China. - news
The company's core business is gravity separation equipment, magnetic separation equipment, ore washing equipment, screening equipment, crushing and grinding equipment, flotation equipment, and mineral conveying equipment. Production of mineral processing equipment, sand gold processing equipment, gold ore processing equipment and Hematite processing equipment and other mineral processing equipment. Our company's gravity beneficiation equipment such as shakers, jigs, and spiral chutes account for 15% of the market share of gravity beneficiation equipment in China. - contact us
