news

Jiangxi Mineral Processing Spiral Chute Plant 1. Overview: The mineral processing chute belongs to the slope flow sorting process. The slurry is fed to a inclined chute or inclined surface, and under the push of water, the mineral particle group is loose and layered. The upper layer of minerals is light and quickly discharged from the outside of the chute, while the lower part of minerals with high specific gravity stagnate inside the chute or slowly discharge from the lower part. After being obtained separately, the concentrate and tailings can be obtained. Glass fiber reinforced plastic chutes are equipment for mining and mineral processing, especially ideal for mining sand by the sea, river beds, sand banks, and streams. The equipment has the characteristics of suitable structure, simple installation, small footprint, easy operation, stable beneficiation, clear separation of ore, high production capacity, high efficiency, ultra-high enrichment ratio, high recovery probability, and reliable operation. There are also advantages such as light weight, moisture resistance, rust resistance, corrosion resistance, and strong adaptability to fluctuations in ore feed volume or concentration, particle size, and grade. 2、 Technical principle: The fiberglass spiral chute mineral separator is not limited to stacking on the cross (or tripod) of the support table. The average mineral mortar is slowly fed onto the spiral groove surface through a feeding groove installed at the end of the rotating groove head for sorting. The tail is equipped with a valve type product selection slot, which divides the selection equipment into three types (or four types) according to grade along the radial direction. Change the cutting width of each product by adjusting the orientation of the valve block. The equipment gathering bucket is a concentric circular tube that allows the obtained multi head ore flow to gather and lead out. The cross section of the spiral chute is particularly suitable for the selection of fine ore particles due to changes in the slope of the curve. Jiangxi Dressing Spiral Chute Factory III. Features This machine is suitable for separating fine materials with Granularity of 0.3-0.02mm to obtain iron, ferrotitanium, ferrochrome, ferrosulfide, zircon, Rutile, monazite, phosphorus, wolframite, cassiterite, tantalum niobium, tantalum niobium ore or other colored metal ores, rare mineral metals and non-ferrous metal minerals with gravity differences. This equipment also has advantages such as stable sorting process, easy control, wide range of allowable changes in ore concentration, high enrichment ratio, high recovery probability, small area occupation, low water consumption, simple structure, no need for power, large production capacity, simple installation, convenient operation, low investment, and fast efficiency. Jiangxi Mineral Processing Spiral Chute Factory 4. The spiral chute is composed of six parts: a feed homogenizer, a feed chute, a rotating chute, a product intercepting chute, an equipment gathering hopper, and a support bracket (including a cross or triangular frame). The spiral groove connected by the rotating plate is a key accessory. The spiral plate is made of fiberglass (fiberglass reinforced with coal gangue) and connected together by bolts. The sorting surface of the rotating groove has a pre made wear-resistant layer. It has the advantages of lightweight, sturdy, and long-lasting consumer goods that are not easily damaged. The spiral groove is equipped with a multi tube feeding homogenizer for ore dressing, which is easy to operate. There is no need to restrict the stacking of mineral sievers on the cross (or tripod) of the support table. The evenly distributed mineral mortar is slowly fed to the surface of the spiral groove through the feeding groove at the beginning of the rotating groove, and then selected for operation. The bottom of the rotating groove is equipped with a valve block type new product selection groove, which allows the sorting equipment to be divided into three categories (or four types) of new products according to grade along the radial direction. Change the acquisition width of each new product by adjusting the position of the valve block. The new product gathering bucket is a concentric circular tube that collects and exports the intercepted variable mineral flows. The cross section and slope of the curve of the fiberglass chute are very suitable for the selection of fine particle materials. Jiangxi Mineral Processing Spiral Chute Factory V. Scope of Application: Fiberglass reinforced plastic spiral chutes are suitable for processing 0.6-0.03mm and vein and placer ores, but high mud content is unfavorable for beneficiation. It is now widely used for processing iron ore, tungsten, tin, niobium tantalum ore, coastal and river sand, and placer gold, among others. Jiangxi Mineral Processing Spiral Chute Factory